Parts List

Below is a list of items needed for this ballast install.  I found that, at least in my area, that it was cheaper to get my plumbing parts from a local plumbing/sprinkler shop rather than big box stores such as Home Depot or Lowes.  I chose to use hose supplied by EVCO House of Hose because it was cheaper and I felt it was higher quality than the ballast hose provided by sites like wakemakers.  Some guys are very particular about their custom install looking like it was installed from the factory.  If that is important to you then this hose is not for you since it is clear with white ribbing instead of solid black.

Your parts will vary obviously depending on your design and whether or not you reuse any stock thru hulls, etc.  Here is an exploded view of the parts.  I found it helpful to create this type of drawing to figure out quantities for each part. (click the drawing for a larger view)



Plumbing
2 - Johnson Ultra Reversible 13.7GPH impeller pumps (shop around online, there are some deals out there)
100 feet - 1" ID hose (Part number 090-1 from EVCO)
50 feet - 3/4" ID hose (Part number 090-3/4 from EVCO)
1 - 1" barb x 1" barb x 3/4" FPT tee
1 - 3/4" MPT x 3/4" male garden hose thread adapter
1 - Garden hose bras end cap
1 - Female garden hose x female garden hose swivel adapter
1 - 1" barb tee
4 - 1" check valves (wakemakers)
3 - 3/4" check valves (wakemakers)
2 - 1" barb x 1" barb x 1" FPT tee
2 - 1" barb x 1" MPT elbow
3 - 1" barb elbow
3 - 3/4" barb elbow
2 - 1" chrome thru hull
1 - 3/4" chrome thru hull
9 - 1" MPT to 1" barb adapter
2 - 1" MPT to 3/4" barb adapter
7 - 1" PVC slip x 1" FPT adapter
2 - 1" PVC slip  x 1" FPT elbow
7 - 1" PVC slip tee
8 - 1" PVC slip ball valve
2 - 1" PVC threaded ball valve
3 feet 1" PVC pipe
2 - 1" MPT x 1" FPT street elbow
2 - 1" close nipple
2 - 3/4" barb plug
1 - roll of thread seal tape
6 - Fly High 1" Quick Release elbow (W746)
6 - Fly High 1" Quick Release x sac thread adapter (W743)
3 - Fly High 3/4" Quick Release elbow (W742)
3 - Fly High 3/4" Quick Release x sac thread adapter (W736)
2 - Fly High check valves (W744) for aux sacs
3 - 1" Y fitting (purchased from D&T Aquarium)
8 - boxes (10 pack) of hose clamps
8 - 1" #8 screws (if I remember right) for mounting pumps
1 - 3M 5200 Fast Cure marine sealant (for chrome thru hulls)
1 - small can of PVC primer
1 - small can of PVC glue
1 - PVC cutter

Electrical
6 - 10 guage wire assorted colors (length will vary)
8 - 10 guage butt connectors
2 - 10 guage ring connectors
22 - 10 guage female spade connectors
6 - spade jumper adapters (as shown in electrical section of this blog)
1 - 30 amp resettable breaker (may need two depending on what is in your boat)
2 - rolls of electrical tape
10 - 8" mounting zip ties
10 - 8" zip ties
10 - 14" zip ties
10 - 1/2" screws, #10. (for mounting zip ties)
1 - Wire stripper/crimping tool
2 - Contura 3 position DPDT switches (purchased here)

No comments:

Post a Comment